![onvif port number onvif port number](https://www.cctvcameraworld.com/cms/wp-content/uploads/hikvision-add-onvif-user-1024x569.png)
Video turbines support only video encoder configuration which is described below. A media profile maps a video and audio source to a video and an audio encoder, PTZ and analytics configurations. ONVIF Media profiles control real-time video and audio streaming configurations. In case it is already set to On, it is required to manually revert it to Off under Relay/Output Settings > Idle Enable control of relay IDLE state: This option is used for suppress forcing of Idle state of Relay Settings to On that some Security systems force.
![onvif port number onvif port number](https://www.foscam.com/Uploads/faqnew/2019-04-18/20190418023924_91507.png)
Use ONVIF port for HTTP tunneling: This option controls whether video stream tunneling over HTTP is using ONVIF port.ONVIF WS-Discovery Location: Sets device location for WS-Discovery that will be shown in ONVIF client after device is found.ONVIF WS-Discovery Name: Sets device name for WS-Discovery that will be shown in ONVIF client after device is found.If this setting is turned off, station can not be discovered by any ONVIF client. Traffic to this port is used for WS-Discovery Service. Enable ONVIF Discovery Service: Enables UDP port 3702 on station firewall.WS-Discovery is standardized ONVIF mechanism for discovering ONVIF devices. ONVIF configuration share the same web page with RTSP configuration. ONVIF settings are available on video Turbine stations only: TCIV-2, TCIV-3 and TCIV-6. Settings defined in this section are used for such integrations.
Onvif port number software#
All Video Management System software (ONVIF client) that conform ONVIF Profile S client specification can be used for integration of video Turbines into the system. Turbine video stations conform ONVIF Profile S device specification standard. ONVIF creates a standard for how IP products within video surveillance and other physical security areas can communicate with each other. ONVIF (Open Network Video Interface Forum) is a global and open industry forum with the goal of facilitating the development and use of a global open standard for the interface of physical IP-based security products. This option is using lots of resources, so it is not recommended to be used. Enable video stream tunneling - defines if tunneling is used in video RTSP stream.On video Turbine stations this option can be defined separately for each stream. With this setting it is possible to choose whether only microphone signal is sent to RTSP stream or both microphone and speaker signals are sent to RTSP stream. Stream Audio Source - defines when acoustic echo canceler is applied to mic+speaker voice.All supported RTSP streams are listed here: audio-only, video-only and audio+video stream URL for video Turbine devices and audio-only stream URL for other Turbine devices. RTSP URL - RTSP URL that can be copied into RTSP player.Enable RTSP Authentication - enables mandatory usage of RTSP credentials on stream setup.RTSP Port - defines RTSP port - by default RTSP port is set to 554.Enable RTSP - enables RTSP traffic by allowing/blocking traffic from/to RTSP port.Click "OK" go to next step, it shows up another new Window guides us to set advanced features of the Blue Iris, and we keep them as untouched, then click "OK" to complete the adding process.Īfter wait 10 or more seconds, the software will display your camera's image.RTSP Settings (Non-Video Turbine stations) 5000Īfter fill above information, click "Find/Inspect" button, the software will inspect media information of the camera, then add "/onvif1" to video path.
Onvif port number password#
192.168.1.7Īccount: user and password information, the default account of the Yoosee camera is admin, 123.ĭiscovery/ONVIF port: the default port number of ONVIF protocol, e.g. The software will pop-up "Network IP camera configuration" window, here we need to fill some information:Īddress: the local IP address of your camera, e.g.
![onvif port number onvif port number](https://camera-sdk.com/attachments/6600/discover-onvif-ip-cameras-on-your-local-network.png)
In new pop-up window, we enter the customized camera name, click "OK" go to next step. Running the Blue Iris software, then click "+" on the top to add a new camera. Blue Iris is one of ONVIF compliant video management software, Yoosee cameras are also compatible with ONVIF protocol, so you can add Yoosee Wi-Fi cameras to Blue Iris software if you using it to manage your other IP cameras from different brands.īefore we add the camera to the Blue Iris software, we need to use the CMSClient software to know its IP address.